Scanning success for printed medical implants

Quality assurance is vital in the production of accurate, patient-specific implants, endoprostheses and surgical guides. Consequently, Baltic Orthoservice in Kaunas, Lithuania uses a multi-sensor CMM including a laser scanner in conjunction with a micro-CT (computed tomography) system, all supplied by Nikon Metrology.

The Altera CMM with LC15Dx laser scanner allows fast inspection of 3D printed implant surfaces and screw holes, while the XT H 225 CT guarantees internal structure quality and accurate geometrical correlation between CAD implant model and manufactured product.

Paulius Lukševičius, engineer of mechanics at Baltic Orthoservice explains: “3D printing is a complicated technology and there is a big variation in processing parameters, so predicting the quality and geometry of printed objects is quite a challenge.

“Patient-specific implants are a bespoke treatment solution, which means that the surgery must be ‘pre-planned’ virtually so the implant can simply be put in place. To be able to execute the virtual plan, it is vital to be 100% sure that the implant geometry is exactly the same as the CAD model and that the holes are machined to high accuracy.

“To fulfil these goals, we use a variety of metrology equipment. The CMM with laser scanner is irreplaceable when we need to perform fast checks after each manufacturing and post-processing stage, especially to check spherical surfaces, bearing surfaces and hole angles.”

Unlike standard modular hip implants used to treat severe clinical conditions, patient-specific alternatives are designed as a single device with anatomically adapted surfaces. It eliminates the risk of instability and adapts the implant to the bone rather than the bone to the implant.

A major benefit of the procedure is that, during surgery, there is no need to shape the bone to adapt it to the implant or use bone cement, meshes and augments to fill the bone defect. The implants are designed using virtual anatomical bone models which are obtained from medical CT scans of a patient.

For manufacturing the implants, Baltic Orthoservice uses direct metal laser sintering equipment purchased in 2012. After 3D printing, implants undergo a variety of post-processing steps, including heat treatment, surface polishing and milling for screw holes. There are a number of medical device standards and regulations that must be met, which is why it is paramount for products to be of ultra-high accuracy.

With fine tolerances and strict standards to be adhered to, the post-processing stages are repeated until the physical implant matches the desired virtual model exactly. Quality assurance measures are taken following every step, during which the LC15Dx laser scanner is able to show quickly how well the physical part matches the virtual model.

Milda Jokymaitytè, clinical engineer at Baltic Orthoservice, explains: “Laser scanning and micro-CT serve two different purposes and both excel in different areas.

“The CMM with laser scanner is very effective for inspecting features and surfaces of bigger parts such as an acetabular implant, for quality control of standard products like osteosynthesis plates and for assessing standard elements in patient-specific implants, i.e. screw holes or spherical shapes.

“The micro-CT system is a vital tool for non-destructive analysis of the internal structure and geometry of additively manufactured components.”

As the Quality Control Laboratory at Kaunas was a new project to supplement the additive manufacturing facilities, there were no previous systems to be replaced. Baltic Orthoservice knew what was required and compared the best technologies on the market to find the right solution.

Mr Lukševičius comments: “The primary requirement was to have the capability to inspect parts made from different types of materials. The size of the working area was also important, but most crucial was accuracy.”

He points out that a key advantage of the Nikon Metrology LC15Dx is its ability to scan reflective and multi-material surfaces thanks to ESP (enhanced sensor performance) technology. It maintains accuracy, speed and data quality by intelligently and continuously adapting the laser settings for each measured point.

Probing error is comparable to that of tactile inspection (1.9μm) and data collection is fast at 70,000 points per second. By maintaining such high standards when scanning difficult surfaces, the LC15Dx is an ideal tool for inspecting complex parts in the medical industry.

Mr Lukševičius concludes: “The Nikon solution offers more in-depth knowledge of what we are manufacturing and gives better precision and understanding of 3D printing errors and deviations. It means we achieve superior product quality and avoid problems during operations. Implants with Nikon quality assurance are more reliable and it is easier to prove their worth.

“Often our quality control laboratory receives inquiries from other manufacturers in the medical sector and other industries to perform geometry inspection for them.”

NIKON METROLOGY www.nikonmetrology.com

Company

Nikon Metrology

Related Articles

HP makes first leap into 3D printing market

Having teased a 3D printer over the last few years, and at 3D Print Week NY last year, HP has finally announced two industrial 3D printers that produce objects ten times faster than any similar printer on the market, and at half the cost.
7 years ago News
Most recent Articles

Renishaw highlights career pathways in engineering

There is not one singular blueprint that can lead to a career in the engineering industry. It offers a variety of roles, open to people from diverse backgrounds. To highlight the diversity of skills and experiences in engineering, global engineering technologies company, Renishaw, has created the ‘Employee perspectives’ series.
3 hours ago News

Login / Sign up